行业标准规范英汉对照-通用零部件1

来源：塑胶五金网发布时间：2007-12-16 15:15:00点击率：

    1 GB/T 2-1985 紧固件外螺纹零件的末端 Fasteners--Ends of parts with external thread
2 GB/T 8-1988 方头螺栓 C级 Square head bolts--Product grade C
3 GB/T 10-1988 沉头方颈螺栓 Flat countersunk square neck bolts
4 GB/T 11-1988 沉头带榫螺栓 Flat countersunk nib bolts
5 GB/T 12-1988 半圆头方颈螺栓 Cup head square neck bolts
6 GB/T 13-1988 半圆头带榫螺栓 Cup head nib bolts
7 GB/T 15-1988 大半圆头带榫螺栓 Cup head nib bolts with large head
8 GB/T 22-1976 小六角头导颈螺栓 Bolts, small hexagon head with fit neck
9 GB/T 23-1976 小六角头螺杆带孔螺栓 Bolts, small hexagon head with hole through the shank
10 GB/T 24-1976 小六角头螺杆带孔导颈螺栓 Bolts, small hexagon head with fit neck and hole through the shank
11 GB/T 25-1976 小六角头头部带孔螺栓 Bolts, small hexagon head with holes through the head
12 GB/T 26-1976 小六角头头部带孔导颈螺栓 Bolts, small hexagon head with fit neck and holes through the head
13 GB/T 27-1988 六角头铰制孔用螺栓 A和B级 Hexagon fit bolts--Product grade A and B
14 GB/T 28-1988 六角头螺杆带孔铰制孔用螺栓 A和B级 Hexagon fit bolts with Split pin hole on shank--Product grade A and B
15 GB/T 29.1-1988 六角头头部带槽螺栓 A和B级 Hexagon bolts with slot on head--Product grade A and B
16 GB/T 29.2-1988 十字槽凹穴六角头螺栓 Cross recessed hexagon bolts with indentation
17 GB/T 31.1-1988 六角头螺杆带孔螺栓 A和B级 Hexagon bolts with split pin hole on shank--Product grade A and B
18 GB/T 31.2-1988 六角头螺杆带孔螺栓细杆 B级 Hexagon bolts with split pin hole on shank--Reduced shank--Product grade B
19 GB/T 31.3-1988 六角头螺杆带孔螺栓细牙 A和B级 Hexagon bolts with split pin hole on shank--Fine pitch thread--Product grade A and B
20 GB/T 32.1-1988 六角头头部带孔螺栓 A和B级 Hexagon bolts with wire holes on head--Product grade A and B 21 GB/T 32.2-1988 六角头头部带孔螺栓细杆 B级 Hexagon bolts with wire holes on head--Reduced shank--Product grade B
22 GB/T 32.3-1988 六角头头部带孔螺栓细牙 A和B级 Hexagon bolts with wire holes on head--Fine pitch thread--Product grade A and B
23 GB/T 35-1988 小方头螺栓 B级 Square head bolts with small head--Product grade B
24 GB/T 37-1988 T型槽用螺栓 Bolts for T-Slot
25 GB/T 38-1976 螺栓技术条件 Bolts--Technical requirements
26 GB/T 39-1988 方螺母 C级 Square nuts--Product grade C
27 GB/T 41-1986 1 型六角螺母 C 级 Hexagon nuts--Style 1--Product grad C
28 GB/T 56-1988 六角厚螺母 Hexagon thick nuts
29 GB/T 61-1976 螺母技术条件 Nuts--Technical requirements
30 GB/T 62-1988 蝶形螺母 Wing nuts
31 GB/T 63-1988 环形螺母 Lifting nuts
32 GB/T 65-1985 开槽圆柱头螺钉 Slotted cheese head screws
33 GB/T 67-1985 开槽盘头螺钉 Slotted pan head screws
34 GB/T 68-1985 开槽沉头螺钉 Slotted countersunk head screws
35 GB/T 69-1985 开槽半沉头螺钉 Slotted raised countersunk head screws
36 GB/T 70-1985 内六角圆柱头螺钉 Hexagon socket cap head screws
37 GB/T 71-1985 开槽锥端紧定螺钉 Slotted set screws with cone point
38 GB/T 72-1988 开槽锥端定位螺钉 Slotted set screws with cone point
39 GB/T 73-1985 开槽平端紧定螺钉 Slotted set screws with flat point
40 GB/T 74-1985 开槽凹端紧定螺钉 Slotted set screws with cup point
41 GB/T 75-1985 开槽长圆柱端紧定螺钉 Slotted set screws withlong dog point
42 GB/T 77-1985 内六角平端紧定螺钉 Hexagon socket set screws with flat point
43 GB/T 78-1985 内六角锥端紧定螺钉 Hexagon socket set screws with cone point
44 GB/T 79-1985 内六角圆柱端紧定螺钉 Hexagon socket set screws with dog point
45 GB/T 80-1985 内六角凹端紧定螺钉 Hexagon socket set screws with cup point
46 GB/T 83-1988 方头长圆柱球面端紧定螺钉 Square set screws with long dog point and rounded end
47 GB/T 84-1988 方头凹端紧定螺钉 Square set screws with cup point
48 GB/T 85-1988 方头长圆柱端紧定螺钉 Square set screws with long dog point
49 GB/T 86-1988 方头短圆柱锥端紧定螺钉 Square set screws with short dog point and cone end
50 GB/T 89-1976 螺钉技术条件 Screws--Technical requirements
51 GB/T 90-1985 紧固件验收检查、标志与包装 eptance inspection,marking and packaging of fasteners
52 GB/T 91-1986 开口销 Split pins
53 GB/T 93-1987 标准型弹簧垫圈 Single coil spring lock washers--Normal type
54 GB/T 94.1-1987 弹

上一篇：行业标准规范英汉对照-通用零部件2

下一篇：德国标准和国际标准、中国标准中英文对照表

转载请注明：转载自塑胶五金网技术频道 http://www.sjwj.com/Liter/
本文链接：http://www.sjwj.com/Liter/LiterDetail_8318.html
版权声明：1.塑胶五金网转载作品均注明出处，本网未注明出处和转载的，是出于传递更多信息之目的，并不意味着赞同其观点或证实其内容的真实性，您同意将自行加以判断并承担所有风险。 2.如转载作品侵犯作者署名权，或有其他诸如版权、肖像权、知识产权等方面的伤害，并非本网故意为之，在接到相关权利人通知后将立即加以更正。联系电话：15014822798
投稿声明：可将稿件直接发至邮箱：234145668@qq.com（主题注明“投稿”），也可直接联系